Object

SCPI Commands :

[SOURce<HW>]:AREGenerator:MARKer:OBJect:DELay
[SOURce<HW>]:AREGenerator:MARKer:OBJect:ONTime
[SOURce<HW>]:AREGenerator:MARKer:OBJect:SOURce

class ObjectCls

Object commands group definition. 3 total commands, 0 Subgroups, 3 group commands

get_delay() → int

# SCPI: [SOURce<HW>]:AREGenerator:MARKer:OBJect:DELay
value: int = driver.source.areGenerator.marker.object.get_delay()

Sets a delay time for the start of the object marker. The delay time delays the marker signal at the marker output relative to the signal generation start.

return:

obj_marker_delay: integer Range: -150000 to 150000

get_ontime() → float

# SCPI: [SOURce<HW>]:AREGenerator:MARKer:OBJect:ONTime
value: float = driver.source.areGenerator.marker.object.get_ontime()

Sets the on time (pulse width) of the object marker.

return:

obj_marker_on_time: float Range: 10 to 150000

get_source() → AregObjMarkSource

# SCPI: [SOURce<HW>]:AREGenerator:MARKer:OBJect:SOURce
value: enums.AregObjMarkSource = driver.source.areGenerator.marker.object.get_source()

Sets the marker source used in the test setup.

return:

obj_marker_source: SETTing| SCENario| HIL SETTing Sets the object marker after a change in the radar object settings. SCENario Requires: [:SOURcehw]:AREGenerator:OSETup:MODE DYNamic and [:SOURcehw]:AREGenerator:OSETup:SOURce SCENario. Sets the object marker at the restart of the replayed scenario. HIL Requires: [:SOURcehw]:AREGenerator:OSETup:MODE DYNamic. For [:SOURcehw]:AREGenerator:OSETup:SOURce HIL: requires [:SOURcehw]:AREGenerator:OSETup:PROTocol ZMQ|DCP|UDP. Sets the object marker according to a timestamp defined in the open simulation interface (OSI) protocol.

set_delay(obj_marker_delay: int) → None

# SCPI: [SOURce<HW>]:AREGenerator:MARKer:OBJect:DELay
driver.source.areGenerator.marker.object.set_delay(obj_marker_delay = 1)

Sets a delay time for the start of the object marker. The delay time delays the marker signal at the marker output relative to the signal generation start.

param obj_marker_delay:

integer Range: -150000 to 150000

set_ontime(obj_marker_on_time: float) → None

# SCPI: [SOURce<HW>]:AREGenerator:MARKer:OBJect:ONTime
driver.source.areGenerator.marker.object.set_ontime(obj_marker_on_time = 1.0)

Sets the on time (pulse width) of the object marker.

param obj_marker_on_time:

float Range: 10 to 150000

set_source(obj_marker_source: AregObjMarkSource) → None

# SCPI: [SOURce<HW>]:AREGenerator:MARKer:OBJect:SOURce
driver.source.areGenerator.marker.object.set_source(obj_marker_source = enums.AregObjMarkSource.HIL)

Sets the marker source used in the test setup.

param obj_marker_source:

SETTing| SCENario| HIL SETTing Sets the object marker after a change in the radar object settings. SCENario Requires: [:SOURcehw]:AREGenerator:OSETup:MODE DYNamic and [:SOURcehw]:AREGenerator:OSETup:SOURce SCENario. Sets the object marker at the restart of the replayed scenario. HIL Requires: [:SOURcehw]:AREGenerator:OSETup:MODE DYNamic. For [:SOURcehw]:AREGenerator:OSETup:SOURce HIL: requires [:SOURcehw]:AREGenerator:OSETup:PROTocol ZMQ|DCP|UDP. Sets the object marker according to a timestamp defined in the open simulation interface (OSI) protocol.